Re: REW 5.19 beta 10
Inviato: 15/07/2018, 23:54
Altro aggiornamento pronto:
Changes in V5.19 beta 10:
24-bit data is now supported where the JVM makes it available (currently macOS and probably Linux)
Added 176.4, 352.8 and 384 kHz to the sample rates allowed for ASIO
Allow generator to continue running if ASIO output selection is changed - audio will be interrupted briefly, however
Added a dBc axis option for the RTA (dB relative to carrier, mainly used to present data relative to the level of the fundamental tone in the signal)
Only stop the generator after SPL calibration if the generator was started by REW
Added a colour scheme for spectrograms and waterfalls based on Dave Green's cubehelix, see https://www.mrao.cam.ac.uk/~dag/CUBEHELIX/
The delay figure with acoustic timing reference now uses the Estimate IR Delay process (cross correlation with minimum phase response) for better results with measurements that do not have HF content (mids or woofers)
Added warning to check mic access is allowed in Windows Privacy settings if input is not accessible
Added an option to allow/disallow narrow filters below 200 Hz when matching to target
Added an option to use IEC263 25 dB/decade aspect ratio when capturing graph images
Changed graph image capture to render the graph directly at the chosen width rather than scaling from the current width
Added a Tone Burst option to the signal generator
The Nimbus look and feel places the file chooser focus on the directory selector instead of the file name field, added a workaround for that
Added options to normalise, apply window and export min phase version to the export impulse response as text dialog
Updated the impedance measurement setup images to make it clearer that outputs and inputs are from the same device
Expanded the RT60 graph help
Bug fix: Aborting measurement for exceeding SPL limit should not apply to impedance measurements
Bug fix: Acoustic timing ref would be one channel out if using Java drivers with a multi-channel output and the ref output wasn't left or right
Bug fix: Spectrogram top level could get set to an incorrect value when changing measurements
Bug fix: Starting phase for signal generator linear or log sweeps was not reset to zero for each new sweep (did not affect measurement sweeps)
Bug fix: The level of custom filtered pink noise was affected by the low and high cut filter frequencies even if the filters were disabled
Changes in V5.19 beta 10:
24-bit data is now supported where the JVM makes it available (currently macOS and probably Linux)
Added 176.4, 352.8 and 384 kHz to the sample rates allowed for ASIO
Allow generator to continue running if ASIO output selection is changed - audio will be interrupted briefly, however
Added a dBc axis option for the RTA (dB relative to carrier, mainly used to present data relative to the level of the fundamental tone in the signal)
Only stop the generator after SPL calibration if the generator was started by REW
Added a colour scheme for spectrograms and waterfalls based on Dave Green's cubehelix, see https://www.mrao.cam.ac.uk/~dag/CUBEHELIX/
The delay figure with acoustic timing reference now uses the Estimate IR Delay process (cross correlation with minimum phase response) for better results with measurements that do not have HF content (mids or woofers)
Added warning to check mic access is allowed in Windows Privacy settings if input is not accessible
Added an option to allow/disallow narrow filters below 200 Hz when matching to target
Added an option to use IEC263 25 dB/decade aspect ratio when capturing graph images
Changed graph image capture to render the graph directly at the chosen width rather than scaling from the current width
Added a Tone Burst option to the signal generator
The Nimbus look and feel places the file chooser focus on the directory selector instead of the file name field, added a workaround for that
Added options to normalise, apply window and export min phase version to the export impulse response as text dialog
Updated the impedance measurement setup images to make it clearer that outputs and inputs are from the same device
Expanded the RT60 graph help
Bug fix: Aborting measurement for exceeding SPL limit should not apply to impedance measurements
Bug fix: Acoustic timing ref would be one channel out if using Java drivers with a multi-channel output and the ref output wasn't left or right
Bug fix: Spectrogram top level could get set to an incorrect value when changing measurements
Bug fix: Starting phase for signal generator linear or log sweeps was not reset to zero for each new sweep (did not affect measurement sweeps)
Bug fix: The level of custom filtered pink noise was affected by the low and high cut filter frequencies even if the filters were disabled